| Publications |
| Alimadadi, M., Mahmoudiniya, M., Goodarzi, M., Boutorabi, S.M.A., "Effect of tool transverse speed and pin offset on the properties of friction stir welding Al6061-St52 dissimilar joint", Journal of Advanced Joining Processes, 2022, 5, 100116 |
| Hosseinzadeh, S. , Goodarzi, M., " Influence of Shielding Gas Composition and Pulsed Current Frequency on the Microstructure of Austenitic Stainless Steel Welded by Pulsed Current GTAW", Transactions of the Indian Institute of Metals, 2022 |
| Khalili, A. , Mojtahedi, M. , Qaderi, A. , Goodarzi, M. , Torkamany, M.J., " Effect of pulse laser parameters on the microstructure of the in-situ Fe-TiC hard layer: Simulation and experiment", Optics and Laser Technology, 2021, 135, 106693 |
| Mahmoudiniya, M. , Kokabi, A.H. , Goodarzi, M. , Kestens, L.A.I., " The Effect of Improved Cooling on the Microstructure and Mechanical Properties of Friction Stir-Welded Advanced High-Strength Dual-Phase Steel", Steel Research International, 2021, 92(2), 2000253 |
| Mosavi, A. , Sajedi Hosseini, F. , Choubin, B. , ... Dineva, A.A. , Rafiei Sardooi, E., " Ensemble Boosting and Bagging Based Machine Learning Models for Groundwater Potential Prediction", Water Resources Management, 2021, 35(1), pp. 23–37 |
| Nabavi, B. , Goodarzi, M. , Khan, A.K., " Investigation of secondary phases and tensile strength of nitrogen-containing Alloy 718 weldment", International Journal of Minerals, Metallurgy and Materials, 2020, 27(9), pp. 1259–1268 |
| Mosavi, A. , Hosseini, F.S. , Choubin, B. , Goodarzi, M. , Dineva, A.A., " Groundwater Salinity Susceptibility Mapping Using Classifier Ensemble and Bayesian Machine Learning Models", IEEE Access, 2020, 8, pp. 145564–145576, 9162111 |
| Mahmoudiniya, M., Kokabi, A.H., Goodarzi, M., Kestens, L.A.I., "Friction stir welding of advanced high strength dual phase steel: Microstructure, mechanical properties and fracture behavior", Materials Science and Engineering A,769,138490, 2020 |
| Choubin, B. , Khalighi-Sigaroodi, S. , Mishra, A. , ... Ghaljaee, E. , Zhang, F., " A novel bias correction framework of TMPA 3B42 daily precipitation data using similarity matrix/homogeneous conditions", Science of the Total Environment, 2019, 694, 133680 |
| Nabavi, B., Goodarzi, M., Khan, A.K., "Metallurgical effects of nitrogen on the microstructure and hot corrosion behavior of Alloy 718 weldment", Materials Characterization, 157,109916, 2019 |
| Shoushtari, M.T., Goodarzi, M., Sabet, H., "Investigation of microstructure and dry sliding wear of hardfaced layers produced by FCAW using cored wire Fe-B-C-Ti alloy", Iranian Journal of Materials Science and Engineering 15(4), pp. 19-3, 2018 |
| Faraji, A.H., Moradi, M., Goodarzi, M., Colucci, P., Maletta, C., "An investigation on capability of hybrid Nd:YAG laser-TIG welding technology for AA2198 Al-Li alloy", Optics and Lasers in Engineering, 2017 |
| Khalili, A., Goodarzi, M., Mojtahedi, M., Torkamany, M.J., "Solidification microstructure of in-situ laser-synthesized Fe-TiC hard coating", Surface and Coatings Technology, Volume 307, 15 December 2016, Pages 747-752 |
| Koushki, A.R., Goodarzi, M., Paidar, M., "Influence of shielding gas on the mechanical and metallurgical properties of DP-GMA-welded 5083-H321 aluminum alloy", International Journal of Minerals, Metallurgy and Materials, Volume 23, Issue 12, 1 December 2016, Pages 1416-1426 |
| Faraji, A.H., Goodarzi, M., Seyedein, S.H., Maletta, C., "Effects of welding parameters on weld pool characteristics and shape in hybrid laser-TIG welding of AA6082 aluminum alloy: numerical and experimental studies", Welding in the World, Volume 60, Issue 1, 1 January 2016, Pages 137-151 |
| Mojtahedi, M., Goodarzi, M., Aboutalebi, M.R., Soleimanian, V., "An investigation on the microstructure and defects in the mechanically milled Cu and Fe powders", Powder Diffraction, Volume 30, Issue 1, 21 October 2015, Pages 14-24 |
Dehkordi, E.N., Samim Banihashemi, H.R. , Naghizadeh, R., Rezaie, H.R., Goodarzi, M., "Synthesis of aluminum nitride in a coke–calcium reduction bed using nitrogen in air", International Journal of Minerals, Metallurgy and Materials, Volume 22, Issue 9, 14 September 2015, Pages 972-976 |
| Faraji, A.H., Goodarzi, M., Seyedein, S.H., Barbieri, G, Maletta, C., "Numerical modeling of heat transfer and fluid flow in hybrid laser–TIG welding of aluminum alloy AA6082", International Journal of Advanced Manufacturing Technology, Volume 77, Issue 9-12, 1 April 2015, Pages 2067-2082 |
| Nabavi, B., Goodarzi, M., Amani, V., "Nitrogen effect on the microstructure and mechanical properties of nickel alloys", Welding Journal, Volume 94, Issue 2, 1 February 2015, Pages 53s-60s |
| Homam Naffakh Moosavy, Mohammad-Reza Aboutalebi, Seyed Hossein Seyedein, Massoud Goodarzi, Meisam Khodabakhshi, Carlo Mapelli, Silvia Barella, " Modern fiber laser beam welding of the newly-designed precipitation-strengthened nickel-base superalloys ", Optics & Laser Technology 01/2014; 57:12–20. · 1.37 Impact Factor |
| Milad Mojtahedi, M. Goodarzi, M.R. Aboutalebi, M. Ghaffari, V. Soleimanian, " Investigation on the formation of Cu–Fe nano crystalline super-saturated solid solution developed by mechanical alloying ", Journal of Alloys and Compounds 02/2013; 550:380. · 2.39 Impact Factor |
| Taghi Dallali Isfahani, Jafar Javadpour, Alireza Khavandi, Massoud Goodarzi, Hamid Reza Rezaie, " Nanocrystalline Growth Activation Energy of Zirconia Polymorphs Synthesized by Mechanochemical Technique ", Journal of Materials Science & Technology. 01/2013; |
| M. Mojtahedi, M. Goodarzi, B. Sharifi, Jalil Vahdati Khaki, " Effect of electrolysis condition of zinc powder production on zinc–silver oxide battery operation ", Energy Conversion and Management 01/2011; 52(4):1876-1880. · 2.78 Impact Factor |
| H. Sabet, Sh. Khierandish, Sh. Mirdamadi, M. Goodarzi, " The Microstructure and Abrasive Wear Resistance of Fe–Cr–C Hardfacing Alloys with the Composition of Hypoeutectic, Eutectic, and Hypereutectic at ",Tribology Letters 01/2011; · 1.74 Impact Factor |
| M. Pouranvari, S. M. Mousavizadeh, S. P. H. Marashi, M. Goodarzi, M. Ghorbani, " Influence of fusion zone size and failure mode on mechanical performance of dissimilar resistance spot welds of AISI 1008 low carbon steel and DP600 advanced high strength steel ", Materials & Design - MATER DESIGN. 01/2011; 32(3):1390-1398. |
| F. Nikoosohbat, S. Kheirandish, M. Goodarzi, M. Pouranvari, S. P. H. Marashi, " Microstructure and failure behaviour of resistance spot welded DP980 dual phase steel ", Materials Science and Technology 05/2010; 26(6):738-744. · 0.75 Impact Factor |
|
M. A. Safarkhanian, M. Goodarzi, S. M. A. Boutorabi “Effect of Rotational Speed ( w ) on the Particles Breakup and Hardness Values in 2024-T851 Friction Stir Welds” Iranian Journal of Materials Science & Engineering, Vol. 6, No. 3, 2009, pp. 7-14
|
|
M. Goodarzi, S.P.H. Marashi, M. Pouranvari, “Dependence of Overload Performance on Weld Attributes for Resistance Spot Welded Galvanized Low Carbon Steel” Journal of Materials Processing Technology, 209 (2009), pp. 4379-4384
|
|
F. Nikoosohbat, S. Kheirandish , M. Goodarzi, M. Pouranvari, S.P.H. Marashi, “Microstructure and Failure Behaviour of Resistance Spot Welded DP980 Dual Phase Steel” Materials Science and Technology, 26 (2010) 738-744.
|
|
M. Ebrahimnia, M. Goodarzi, Meisam Nouri, Mohsen Sheikhi, “Study of the Effect of Shielding Gas Composition on the Mechanical Weld Properties of Steel ST 37-2 in Gas Metal Arc welding” Materials and Design, 30 (2009), pp. 3891-3895
|
|
B. Sharifi, M. Mojtahedi, M. Goodarzi, J. Vahdati Khaki, “Effect of Alkaline Electrolysis Conditions on Current Efficiency and Morphology of Zinc Powder” Hydrometallurgy, 99 (2009), pp. 72-76
|
|
M. A. Safarkhanian, M. Goodarzi, S. M. A. Boutorabi “Effect of Abnormal Grain Growth on Tensile Strength of Al-Cu-Mg Alloy Friction Stir Welded Joints” Journal of Material Science, Vol. 44, 2009, pp. 5452-5458
|
|
M. Ebrahimi-Basabi, J. Javadpour, H. Rezaie, M. Goodarzi, “ Mechanochemical Synthesis of Alumina Nanoparticles” Iranian Journal of Materials Science & Engineering, Vol. 6, No. 1, 2009, pp. 26-30
|
| M. Ebrahimi, J. Javadpoor, H. Razaie, M. Goodarzi, " Mechanochemical synthesis of alumina-zirconia nanocomposite powder", Advances in Applied Ceramics, Vol. 107, No. 6, 2008, pp. 318-321 |
|
P. Marashi, M. Pouranvari, S. Amirabdollahian, A. Abedi, M. Goodarzi, "Microstructure and Failure Behavior of Dissimilar Resistance spot Welds between Low Carbon Galvanized and Austenitic Stainless Steels" Materials Science and Engineering A, Vol. 480, Nos. 1-2, 2008, pp. 175-180
|
| M. Asadi, M. Goodarzi, S. Kheirandish, "Kinetics of austenite formation in dual phase steels", Journal ISIJ International, Vol. 48, No. 9, 2008, pp. 1251-1255 |
|
M. Pouranvari, A. Abedi, P. Marashi, M. Goodarzi, "Effect of Expulsion on Peak Load and Energy Absorption of Low Carbon Steel Resistance Spot Welds" Science and Technology of Welding and Joining, Vol. 13, No. 1, 2008, pp. 39-43
|
|
M. Pouranvari, H. R. Asgari, S. M. Mosavizadeh, P. H. Marashi, M. Goodarzi, “Effect of weld nugget size on overload failure mode of resistance spot welds”, Science & Technology of Welding and Joining, Vol. 12, No. 3, 2007, pp. 223-231
|
|
P. Marashi, M. Pouranvari, S. M. Sanaee, A. Abedi, S. H. Abootalebi, M. Goodarzi, “Relationship between failure behaviour and weld fusion zone attributes of austenitic stainless steel resistance spot welds”, Material Science & Technology, Vol. 24, No. 12, 2008, pp. 1506-1512
|
|
M. Goodarzi, R.T.C. Choo, J.M. Toguri, “Electrode effect on flow conditions in Argon Gas metal arc modeling”, Iranian Journal of Materials Science & Engineering, Vol. 1, No. 1, 2004
|
| A. H. Tavakoli, M. Goodarzi, "Effect of Mechanical Activation on Carbothermic Synthesis of Titanium Carbide from Ilmenite Concentrate", Iranian Journal of Materials Science and Engineering Vol. 1, No. 3, Summer 2004, pp. 22-27 |
| M.Pouranvari, P.Marashi, M.Goodarzi, H.Bahmanpour" An analytical model predicting failure mode of resistance spot welds" Materials science & technology(MS&T),2008 |
| M.Pouranvari, P.Marashi, M.Goodarzi,A.Abedi" An analytical model predicting failure mode of resistance spot welds" METAL,2008 |
| M.Pouranvari, P.Marashi, M.Goodarzi "Failure mode of dissimilar resistance spot welds between austenitic stainless and low carbon steels " METAL,2008 |
| M.Pouranvari,P.Marashi, M.Goodarzi" Failure behavior of low carbon steel resisyance spot welds under tensile-shear and coach-peel static loading condition" METAL,2008 |
|
/goodarzi.jpg)
iust.ac.ir