Iranian Journal of Materials Science and Engineering

---

The hot cracking susceptibility can be determined by establishing the transition temperature between brittle and ductile fracture at high temperature tensile testing of in situ solidified samples. High temperature tensile properties were determined for commercial cathodic pure Cu and Cu- 30%Zn alloy. The transition temperatures for pure Cu and Cu-30%Zn were evaluated from ultimate tensile stress, true strain and area reduction at different testing temperatures. The results show that hot cracking in pure Cu also occurred below and near to its melting temperature. It can be proposed that in this case excess vacancies and vacancy diffusion and condensation are the dominating mechanisms for hot crack formation. The transition temperature for Cu- 30%Zn was much lower than its solidus temperature and this alloy has more susceptibility to hot cracking as compared to pure Cu. The effect of two different cooling rates (15 °C/min and 60 °C/min) on the transition temperature was investigated. The results show that by increasing cooling rate, the transition temperature will increase. The morphology of fracture surfaces for both ductile and brittle modes were evaluated by SEM Two different morphologies, i.e. interdendiritic and intergranual fracture, was found.

---

A mixture of Tio2+Al+C powders was mechanically activated using a planetary ball mill under different milling conditions wherein the milled powders were further subjected to combustion synthesis to produce TiC+Al2O3 composite. The mechanically alloyed powders were characterized by X-Ray diffraction analysis and TEM investigations. XRD analysis of milled powder mixture showed no significant reaction between TiO2, Al and C while a significant amorphization of powder mixtures was observed. TEM analysis indicated the formation of a composite structure of powder particles after milling. The subsequent thermal treatment of the milled powder mix showed that the milling of initial powder mixture under dry environment using mixed large and small balls had a great effect on reaction efficiency and yielded to the highest TiC + Al2O3 ratio in the synthesized products.

---

Partially stabilized zirconia (PSZ) has been proven to be an excellent candidate as a thermal barrier coating (TBe) for hot sections in, for instance, heat or internal combustion engines and gas turbine parts. The main functions of these coatings are reducing heat losses, reducing fuel consumption, increasing efficiency, and extending durability and life. One of the main problems involved is wear behavior in the development of such coatings for these applications. Using the air plasma spraying (APS) technique, conventional and nanostructured 8 wt % yttria partially stabilized zirconia (Y-PSZ) coatings were deposited on austenitic stainless steel (AISI304) disc-shaped substrates. The coated substrates were subjected to pin-on-disc wear tests, using 10 mm silicon nitride and zirconia balls as the pin. The coefficient of friction was recorded in real time. The weight loss of coated substrates was measured. Coatings were characterized before and after being subjected to wear testing by various techniques including optical microscopy, scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and X-ray diffraction (XRD). Effects of various experimental parameters such as wear distance, test temperature, and counter face material were also investigated. Results obtained revealed that, regardless of experimental conditions applied, the nanostructured zirconia coating shows better wear and tribological properties than that of the conventional one.

---

Wear of various basic refractory materials to substitute to currently used magnesia chrome bricks has been studied, measuring matte and slag penetration and dissolution, through different cup and rotary slag tests. High magnesia with and without impregnation, magnesia graphite, magnesia-alumina spinel with and without impregnation, olivine-magnesia and olivine magnesia- graphite bricks, as well as magnesia-graphite and olivine magnesia castables, have been tested. It has been shown that carbon impregnation and graphite introduction into basic refractories are feasible ways to enhance their corrosion-dissolution and penetration resistance against fayalite as well as calcium-ferrite slags. Olivine-based refractories (castables or bricks) may be considered as viable candidates to use in copper-making furnaces. At this point, evaluation of the thermo-mechanical properties of this new class of materials is still missing.

---

A film of osteoconductive and biocompatible material on biomedical metallic implants can create bioactivity of the implant and shorten healing time. Hydroxyapatite, that is the most important mineral part of human bone, was coated on Ti6Al4V using cathodic electrode position process. Pulse electrode position technique was used and the effects of different parameters such as potential, duty cycle (on time/ (on time+ off time)), temperature and current density on the morphology of the deposits were examined. Nano size deposits were formed under controlled temperature and optimization of voltage and current density.

---

In this research the influence of Ti contents on the amounts of inclusions formation and mechanical properties of a high alloy high strength steel, C300, has been investigated. For this purpose several bars were casted under the same solidification conditions, but different amounts of Ti element. All the seven casted bars were homogenized at 1200°C for a period of 2 hours. Then, they were immediately hot rolled after homogenization so that the out rolling temperature was kept in the range of 1000-1200° C. The specimens were then solution annealed at 820°C for hour and finally they were aged for a period of 3 hours at 500°C. The samples were subjected to tensile, impact and hardness tests in order to relate the variation in volume percent of inclusions due to different amount of Ti, to mechanical properties. The results showed that by increasing the amount of Ti a serious decline in toughness properties of the alloy due to increase in inclusion population occurred. So this research provides a very useful information about the relation between volume fraction of inclusions and mechanical properties of a C300 high strength steel.

---

In this study the hot deformation behaviour of a precipitation hardened (PH) stainless steel at high strain rates has been predicted through hot compression testing. Stress-strain curves were obtained for a range of strain rates from 10-3 to 10+1 S-1 and temperatures from 850 to 1150°C. Results obtained by microstructure and stress-strain curves show that at low temperatures and high strain rates, where the Zener-Holman parameter (Z) is high, work hardening and dynamic recovery occure. By increasing temperature and decreasing strain rate, the Z parameter is decreased, so that dynamic recrystallization is the dominant softening mechanism. The results were fitted using a Log Z versus Log (sinh (a sp) diagram allowing an assessment of the behavior of the stresses measured at strain rates closer to those related to the industrial hot rolling schedules. It is clearly shown that the data collected from low strain rate testing can be fairly reasonably extrapolated to higher orders of magnitude of strain rate.

---

In this study, commercially pure titanium/304L stainless steel explosion bonded clads have been annealed under argon atmosphere over the temperature range of 700-900°C for 1h.Microstructure of the clads have been investigated before and after anealing. X-ray diffraction studies revealed that the annealing products in the form of intermetallic phases were gradually formed at the interface of the annealed clads. It was also found that, the bonding zone width increased with temperature according to an Arrhenius type equation. On the base of this equation, the activation energy of bonding zone growth was found equal to about 66.5 kJ/mol. The bond strength of the diffusion annealed clads were evaluated stress relieved. The maximum average tensile strength of ~350MPa was obtained for the as-welded clad. It was found that the bond strength decreased with annealing at 700°C due to an increase in the width of brittle intermetallic layer.

---

TRIP (TRansformation- lnduced- Plasticity) behavior is a powerful mechanism to improve mechanical properties. The basis of TRIP phenomena is the transformation of retained austenite with optimum characteristics (volume fraction, stability, size and morphology) to martensite during deformation at room temperature. Accordingly, the first requirement to obtain desired TRIP effects is to produce an appropriate microstructure. Thermo mechanical processing is an effective method to control the microstructural evolution thereby mechanical properties in TRIP steels. This work deals with a TRIP steel containing 0.2% C, evaluating the effects of straining before and during ?®a atransformation on its final characteristics, using hot compression tests. The results revealed that straining in the two phase region (dynamic transformation) not only reduces the ferrite grain size more significantly, but also increases the retained austenite volumefraction. Accordingly the final mechanical properties were also improved.

---

In the present study a Finite Difference Method has been developed to model the transient incompressible turbulent free surface fluid flow. A single fluid has been selected for modeling of mold filling and The SOLA VOF 3D technique was modified to increase the accuracy of simulation of filling phenomena for shape castings. For modeling the turbulence phenomena k-e standard model was used. In order to achieve an accurate model, solving domain was discrete to three regions includes: laminar sub layer, boundary layer and internal region. This model was applied to experimental models such as a driven cavity, Campbell benchmark [1] and top filled cavity. The results show that the suggested model yield favorable predictions of turbulence flow and have a good consistency in comparing with experimental results.

---

Although the flash smelting technologies use different furnace designs, the refractory linings are exposed to very similar aggressive environments and, as a result, the corrosion analysis results on one type of furnace could be generally applied to other furnaces of similar high temperature processes. Particularities regarding the different chemistries of the pyrometallurgical process and operating parameters of these furnaces could also bring particular aspects to be considered when analyzing the refractory ware and final failure in use. This paper presents a review of the existent experimental. data of corrosion analyses on refractory linings used in two particular flash furnaces for zinc-lead and respectively nickel-copper smelting. Although various modern water cooling systems are generally used to protect the refractory wall linings against corrosion by molten slag and matte, the performance of the refractory roof lining, usually used without water cooling, represents a permanent concern and the object of research studies to extend their life in service. The failure mechanisms analysed in this study are based on postmortem analyses and laboratory corrosion experiments with magnesite-chrome bricks of different chemical and mineralogical compositions. The gaseous atmosphere, usually rich in SO2 and/or CO and various metal fumes, produces irreversible microstructural changes which could shorten the life in service of the refractory lining. The experimental data proved that thermal cycling in SO2/SO3 atmospheres could bring more damage than a continuous use at relatively constant temperature, due to the magnesium and calcium sulphate formation. The laboratory experiments and postmortem analyses showed that that metal fumes at various partial pressure of oxygen would condense as oxides and react inside the pores and at the grain boundaries, contributing to the continuous deterioration of the ceramic matrix of the refractory brick lining. The mechanisms of corrosion, discussed based on laboratory experiments, were confirmed by the postmortem analyses on brick samples used in the industrial flash smelting furnaces.

---

geopolymer cement (inorganic polymeric binder) based on natural pozzolan are investigated. SiO

of activator and total molar ratios of Nacomposition exhibiting the highest 28-day compressive strength. Mixtures exhibiting the highest compressive strength were studied for their molecular structure using laboratory technique of Fourier transform infrared spectroscopy.Results obtained confirm that changes in chemical composition and curing condition can result in variations in degree of silicon substitution by aluminum in the second coordination sphere. Hydrothermal curing affects the molecular structure so that by increasing the hydrothermal curing temperatures, a lower degree of silicon substitution by aluminum in the second coordination sphere is observed. The molecular structure of the studied inorganic polymeric binde is composed of Si-O-Si chains bonded to Al-O and Si-O units creating two and three dimensional networks.

In this paper, the effects of chemical composition and curing conditions on molecular structure of2/Na2O molar ratio2O/Al2O3, and H2O/Al2O3 were changed to determine the optimum chemical

---

Abstract: The risks of alternating current (AC) corrosion and overprotection increasingly demand new criteria for
cathodically protected pipelines. To assess the risk of AC corrosion, new cathodic protection (CP) criteria have been
proposed based on DC/AC current densities measurements using coupons. The monitoring system designed for this
project was based on the instant-off method, with steel coupons simulating coating defects on a buried pipeline. The
problems associated with the instantaneous off-potential measurements have been attributed to a non-sufficient time
resolution. In present study, it has been possible to determine the de-polarisation of steel coupon within a few
milliseconds after disconnecting the coupon from the DC/AC power source, by increasing data acquisition rate. For
this, a monitoring system was developed in order to measure the IR-free potential together with the DC/AC current
densities. The monitoring system was utilized for both laboratory experiments and site survey to study the mechanism
and the condition of AC corrosion, its mitigation and more importantly to define new CP criteria.

---

Abstract: In this paper, a DRIE process for fabricating MEMS silicon trenches with a depth of more than 250 m is described. The DRIE was produced in oxygen-added sulfur hexafluoride (SF6) plasma, with sample cooling to cryogenic temperature using a Plasmalab System 100 ICP 180 at different RF powers. A series of experiments were performed to determine the etch rate and selectivity of the some masking materials such as resists, and metal (Al). Experiments show that different materials have different etch rates, but for the Al mask, an etch rate of 5.44x10-3 nm/min was achieved, that exhibits very stronger resistance against RIE than resists. By controlling the major parameters for plasma etch, an etch rate of 2.85 microns per minute for silicon and a high selectivity of 5.24x105 to the Al etch mask have been obtained. A 90 min etching experiments using etching gas SF6 of 60 standard cubic centimeters per minutes (sccm) with oxygen (13 sccm) were performed by supplying RF power of 5 W to an ICP of 600 watts, and silicon etching process with a depth of 257 m was demonstrated. Our experiments show that Al is the best mask material for very deep trenches in silicon.

---

Abstract:

transition and heat affected zones formed during surface remelting (in order to improve wear resistance) with TIG

process has been investigated. Relationship between various TIG parameters and thickness of remelted and heat

affected zones revealed that a high concentrated heat energy is imposed by TIG process which makes it a proper option

for focused surface treatment. Based on microstructural examinations five areas with different microstructure and

microhardness were identified within the surface area. Graphite flakes were totally dissolved within the first area

leading to the transformation of denderitic austenite to plate martensite and the formation of ledeburite within

interdenderites. The main feature of the second area, resulted from the presence of graphite flakes, was the local

melting with a gap in the vicinity of graphite flakes and that of third area was the formation of finer and denser

martensite plates closer to the graphite flakes compared with those formed at a further distance. In the fourth layer

there is a mixture of martensitic and pearlitic matrix while the matrix of fifth layer has no change of microstructure.

In this study the effect of graphite flakes present in a pearlitic grey cast iron on the microstructure of melted,

---

Abstract:

fabricated. Modifications carried out in different parts of the old system in order to control most

of the growth parameters with more accuracy. The fabricated system was used to grow sapphire

single crystals with almost 10 mm in diameter and 50 mm in length. The crystallinity and

structure of the grown crystals were characterized by computer aided single crystal X-ray

diffraction technique.

A Verneuil system, more sophisticated than a conventional one, has been designed and

---

Abstract:

materials can be fabricated by sintering of W-Cu composite powders. In this research W-20%wt Cu composite powders

was synthesized via a co-precipitation method. Precipitate obtained from a mixture of copper nitrate and ammonium

paratungstate (APT) in distilled water contained W-Cu compounds. This precipitate was washed, dried and calcined

at 550

of dried precipitate powder was determined by thermogravimetry (TG), differential thermal analysis (DTA) and X-ray

diffraction (XRD). The sintering of the reduced powders was investigated as a function of temperature. Relative density

of more than 98% obtained for the powders sintered at 1200

close to theoretical calculations. The hardness of the sintered powders was 320 Vickers.

W-Cu composites are widely used as contacts, heat sinks and electro discharge electrodes. These kinds of°C in air and then reduced in H2 atmosphere in order to convert to W-Cu powders. The calcination temperature°C . The corresponding electrical conductivity was too

---

Abstract:

the changes of BET surface area of a mineral substance during intensive grinding process. Validity of the proposed

model was tested by the experiments performed using a natural chalcopyrite mineral as well as the published data. It

was shown that the model can predict the experimental results with a very good accuracy and can be used to predict

what may happen under the similar experimental conditions.

Based on experimental observations, a model has been developed to describe the effect of grinding time on

---

Abstract: In this paper‚ the physical and mechanical properties of Al nanocomposite reinforced with CNTs wereinvestigated. High purity Al powder and Carbon Nanotubes (CNTs) with different percentage were mixed by ballmilling method and the composite was fabricated by cold pressing followed by sintering technique. The variation ofdensity and hardness of composite with CNTcontent was investigated. The microstructure of composite was evaluatedby SEM (Scanning Electron Microscope) and XRD (X -Ray Diffraction). The results show that the density and hardnessincrease with CNTpercentage.

---

Abstract: Multiwalled carbon nanotubes (MWCNTs) were coated with MgO nano particles using simple precipitationmethod. The growth of Mg(OH)2particles was controlled by adjusting the alkaline concentration, salt concentrationand feed rate in simple precipitation method. The nanometer-sized Mg(OH)2particles were precipitated on the surfaceof functionalized MWCNTs by reaction between MgSO4 solution and NH4OH. The samples have been characterizedby scanning electron microscopy, energy dispersive X-ray spectrometry, X-ray diffraction and thermal gravimetricanalysis. The results showed a nominally complete MgO coating over the entire outer surface of MWCNTs resulting inimprovement of their oxidation durability.