Showing 111 results for Ali
Mohammad Derakhshani, Saeed Rastegari, Ali Ghaffarinejad,
Volume 22, Issue 1 (March 2025)
Abstract
In this research, the morphology of the Ni-W coating was modified by adding graphene oxide (GO) nanosheets in such a way that a foam-like structure with high porosity and holes in the form of intertwined tunnels was obtained. Different amounts of GO nanosheets were added to the plating bath and the resulting coating was examined. In order to estimate the electrochemically active surface area, the cyclic voltammetry (CV) test was used. Moreover, the linear polarization test (LSV) and chronoamperometry in 1 M NaOH were conducted to investigate the electrocatalytic activity for the hydrogen evolution reaction (HER). It was found that by adding 0.4 g/L GO to the electroplating bath, the electrocatalytic properties are doubled and the active surface of the electrode is significantly increased.
Divya Bajpai Tripathy, Anita Kushwaha, Smrita Singh, Smriti Dwivedi, Anjali Gupta, Lalit Prasad, Ashutosh Chauhan,
Volume 22, Issue 2 (JUNE 2025)
Abstract
Organosilicon compounds represent a fascinating class of molecules with diverse structures, unique bonding characteristics, and wide-ranging applications across various fields. The structural diversity of organosilicon compounds arises from the versatility of silicon, which can form a variety of chemical bonds, including single, double, and triple bonds with carbon, as well as bonds with other heteroatoms such as oxygen, nitrogen, and sulfur. This diversity enables the synthesis of an extensive range of organosilicon molecules, including silanes, siloxanes, silanols, silazanes, and silsesquioxanes, among others. The unique properties of these compounds, such as thermal stability, chemical inertness, and flexibility, make them valuable building blocks for the design of advanced materials.Organosilicon compounds find applications in diverse fields, including materials science, pharmaceuticals, electronics, and agriculture. In materials science, they are used as coatings, adhesives, sealants, and modifiers to impart desirable properties such as water repellency, thermal resistance, and biocompatibility. In the pharmaceutical industry, organosilicon compounds serve as drug delivery agents, imaging agents, and synthetic intermediates due to their biocompatibility and tunable properties. In electronics, they are employed as dielectric materials, insulators, and encapsulants in semiconductor devices. Current review aims to unlock new opportunities for the development of innovative materials and technologies with enhanced performance and functionality.
Zainab Dhyaa Fawzy, Saja Ali Muhsin, Taha Hassan Abood,
Volume 22, Issue 2 (JUNE 2025)
Abstract
Ceramics in dentistry have been mainly recommended from a cosmetic perspective. Yet, the hardness behaviour may limit the application in many cases. Although amber glass is used for medications and chemicals, no studies focus on using amber glass for dental purposes as an additive material. This study aims to investigate the dark amber glass behaviour as a new additive material for dental ceramics. The amber glass powder was prepared using the ball mill technique. For the amber glass powder characterization, the SEM/EDX, particle size, DSC, Ion release, and XRD analysis were tested compared to VITA Lumex® AC ceramic. In addition, the Vickers hardness test was applied for ceramic and ceramic amber with an addition of 0.01g, 0.03g, and 0.05g amber glass powder following the DIN EN ISO 6872/ 2019. Statistically, the ANOVA (post hoc- Tukey) test was used for hardness testing analysis at a significant P-value of (P≤0.05). The results show that the amber glass behaviour and composition elements seem similar to VITA ceramics. The addition of amber glass powder to ceramic shows an increase in the HV hardness of specimens. Overall, it was concluded that the amber glass powder could be a promising material for ceramics to use as an additive powder.
Seyed Hossein Razavi, Amirhossein Riazi, Alireza Khavandi, Mostafa Amirjan, Mohsen Ostad Shabani, Hossein Davarzani, Yazdan Shajari,
Volume 22, Issue 2 (JUNE 2025)
Abstract
Additive manufacturing (AM) of metallic parts has gained significant attention in recent years due to its ability to produce components without traditional tooling such as molds, melting furnaces, or extensive raw material preparation. Its unique capability to fabricate complex geometries has revolutionized part design and enabled substantial weight reduction. This review first outlines the development trajectory of metal-based AM, with a particular focus on laser-based fusion methods, including Laser Powder Bed Fusion (LPBF) and Direct Laser Deposition (DLD). Understanding this evolution helps researchers identify both the capabilities and limitations of AM technologies, thereby enhancing their application in areas such as prototyping, mass production, and repair. Each metal possesses unique physical and chemical properties, which often make traditional manufacturing methods more challenging—especially for alloys with high strength, hardness, or temperature resistance. In this context, the review then focuses on nickel-based superalloys (NBSAs), which are widely used in high-temperature and high-stress environments but are particularly difficult to process using conventional techniques. Their application serves as a representative case study for evaluating the performance and feasibility of AM techniques for advanced materials. Furthermore, the future prospects of AM are discussed, including advancements in monitoring systems, integration of machine learning, and the development of AM-specific alloys. As a novel aspect, this work compares LPBF and DLD in terms of their advantages, limitations, and resulting material properties, along with a comparison to traditional manufacturing methods such as casting and wrought processing.
Ali Keramatian, Mohammad Hossein Enayati, Fatemehsadat Sayyedan, Sima Torkian,
Volume 22, Issue 2 (JUNE 2025)
Abstract
The aim of this study was to investigate the effect of current density on the microstructure of electrodeposited Ni–WC–TiC composite coatings on 304 stainless steel and compare the corrosion resistance of the coating and substrate in a 3.5 wt.% sodium chloride solution. A Watts nickel bath was employed under direct current (DC) conditions. Microstructure, elemental composition, and phase composition analyses were conducted using scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD), respectively. The results revealed that the coating formed at a current density of 40 mA/cm² exhibited a denser microstructure with higher cohesion and uniformity compared to coatings produced at other current densities. The corrosion resistance of the coating and substrate was evaluated using Tafel and electrochemical impedance spectroscopy (EIS) analyses. The corrosion test results indicated that the substrate exhibited superior corrosion resistance compared to the coating. Based on the dynamic polarization test plots, the corrosion mechanism of the substrate is active-quasi passive, with a pseudo-passive layer forming on the sample which remains stable within the potential range of -0.17 to 0.17 V. Beyond this potential range, the sample becomes susceptible to pitting. In the coated sample, the corrosion behavior is similar to that of the substrate, with the exception that the pseudo-passive layer remains stable within a narrower potential range of -0.19 to 0.08 V.
Amin Rezaei Chekani, Malek Naderi, Reza Aliasgarian, Yousef Safaei-Naeini,
Volume 22, Issue 2 (JUNE 2025)
Abstract
This paper presents the novel fabrication method of a three-dimensional orthogonally woven (3DW) C/C-SiC-ZrB2 composite and the effects of ZrB2 and SiC particles on microstructure and the ablation behavior of the C/C–SiC–ZrB2 composite are studied. C/C–SiC–ZrB2 composite was prepared by isothermal-chemical vapor infiltration (I-CVI), slurry infiltration (SI), and liquid silicon infiltration (LSI) combined process. Pyrolytic carbon (PyC) was first infused into the 3DW preform by I-CVI at 1050°C using CH4 as a precursor in order to form a C/C preform with porous media. The next step was graphitization at 2400°C for 1hr. Then ZrB2 was introduced into 3DW C/C preform with a void percentage of 48 by impregnating the mixture of ZrB2 and phenolic resin, followed by a pyrolysis step at 1050°C. A liquid Si alloy was infiltrated, at 1650 °C, into the 3DW C/C composites porous media containing the ZrB2 particles to form a SiC–ZrB2 matrix. An oxyacetylene torch flame was utilized to investigate The ablation behavior. ZrB2 particles, along with the SiC matrix situated between carbon fiber bundles, form a compact ZrO2-SiO2 layer. This layer acts as a barrier, restricting oxygen infiltration into the composite and reducing the erosion of carbon fibers. The findings were supported by FESEM imaging and further confirmed through x-ray diffraction and EDS analysis. The addition of ZrB2 to the C/C-SiC composite resulted in a lower mass and linear ablation rate; 2.20 mg/s and 1.4 µm/s respectively while those for C/C-SiC composite were 4.8 mg/s and 6.75 µm/s after ablation under an oxyacetylene flame (2500°C) for 120 s.
Sara Ahmadi, Bijan Eftekhari Yekta, Alireza Mirhabibi,
Volume 22, Issue 3 (September 2025)
Abstract
The crystallization behavior and photocatalytic properties of the sol-gel derived glass ceramic coatings in the TiO2-SiO2-B2O3 system were studied. the prepared sol was sprayed on a glazed ceramic wall. Following drying, the coated specimens were fired at 900°C for 1 h. The impact of boron oxide content in the composition was explored in terms of anatase stability and glass maturing temperature. The thermal and crystallization behaviors of the dried gels were studied by the STA, XRD, and FESEM. The photocatalytic property of the coated layer was examined using methylen blue degradation. Based on the results, the sample containing 15 wt% of boron oxide demonestrated about 30% dye removal efficiency, after only 60 min of UV-irradiation. Additionally, this particular sample exhibited the greatest magnitude of the anatase phase in comparison to the other samples.
Mohammad Abdullah Al Asad, Hasan Ridoy, Md. Shuzon Ali, Mst. Jeba Maimuna,
Volume 22, Issue 3 (September 2025)
Abstract
Perovskite materials have accumulated considerable attention in recent years for their exceptional electro-optical properties, creating them rising candidates for various uses in the fields of photovoltaics, light-emitting devices, and beyond. Among these perovskite materials, CsPbI3 stands out as a notable example due to its remarkable stability, tunable bandgap, and efficient light-emitting properties. The crystal structure, composition, and introductory properties of CsPbI3 perovskite using density functional theorem (DFT) being focused. In detailed exploration of Electronic property, Elastic property, Optical property, Population analysis, and shedding light on the unique attributes of this material highlighted this study. To do above computation we have used CASTEP in Material Studio.
Farzaneh Sadat Teimoory Toufal, Alma Kalali, Arvin Attari Navab, Mohadeseh Reyhani, Hamidreza Rezaie, Jafar Javadpour,
Volume 22, Issue 3 (September 2025)
Abstract
Glass ionomer cements (GICs) are widely utilized in clinical restorative dental applications, which suffer from poor mechanical strength. Recent research shows that GIC achieves optimal performance when modified with lower percentage of filler materials, particularly when using nanoparticles, due to the resultant increase in surface area and packing density of the cement. Notably, while some modifications show promise, others fail to deliver improvements in material characteristics. This study addressed a gap in the literature by investigating the impact of acidic/basic additives, such as Diopside (CaMgSi2O6) and Zirconia (ZrO2), on the properties of the cement. The reactivity of zirconia and Diopside differ distinctly from traditional calcium-aluminosilicate glass when exposed to acidic conditions in GICs. Also, to clarify the impact of acidity/basicity on filler reactivity during cement setting, the potential mechanical enhancement effects by using nano-sized particles is limited to submicrons. This research incorporated Diopside at concentrations of 2, 4, and 6 wt.%, and zirconia at 8, 10, and 12 wt.% into a glass powder component. Results demonstrated that adding 8 wt.% Zirconia led to a 49% enhancement in compressive strength, also improve microhardness by 16 wt.%, attributed to its non-reactive nature, minimal dissolution, and high inherent strength of ZrO2. In contrast, Diopside had a detrimental effect due to its basic nature compared to that of glass powder. These findings highlight the potential of zirconia as a valuable reinforcing material for the successful mechanical performance of glass ionomer cements. Conversely, basic fillers like diopside appear unsuitable for achieving improved mechanical performance in these systems.
Ali Azari Beni, Saeed Rastegari,
Volume 22, Issue 3 (September 2025)
Abstract
Aluminide coatings are widely used in high-temperature applications due to their excellent corrosion resistance and thermal stability. However, optimizing their composition and thickness is crucial for enhancing performance under varying operational conditions. This study investigates the optimization of aluminide coatings through a data-driven approach, aiming to predict the coating thickness based on various composition and process parameters. A comparative analysis of six machine learning models was conducted, with the k-nearest neighbors regressor (KNNR) demonstrating the highest predictive accuracy, yielding a coefficient of determination R² of 0.78, a root mean square error (RMSE) of 18.02 µm, and mean absolute error (MAE) of 14.42. The study incorporates SHAP (Shapley Additive Explanations) analysis to identify the most influential factors in coating thickness prediction. The results indicate that aluminum content (Al), ammonium chloride content (NH4Cl), and silicon content (Si) significantly impact the coating thickness, with higher Al and Si concentrations leading to thicker coatings. Zirconia (ZrO2) content was found to decrease thickness due to competitive reactions that hinder Al deposition. Furthermore, the level of activity in the aluminizing process plays a crucial role, with high-activity processes yielding thicker coatings due to faster Al diffusion. The pack cementation method, in particular, produced the thickest coatings, followed by gas-phase and out-of-pack methods. These findings emphasize the importance of optimizing composition and processing conditions to achieve durable, high-performance aluminide coatings for high-temperature applications.
Khashayar Zamani, Majid Tavoosi, Ali Ghasemi,
Volume 22, Issue 4 (December 2025)
Abstract
The present work, set out with the aim of studying the effect of in-situ precipitation of TiO2 form Ti3C2Tx MXene phase on the electromagnetic (EM) behavior of Ti3C2/TiO2 composites. In this regard, Ti3C2Tx MXene phase was synthesized using HF acidic etching of Ti3AlC2 MAX phase and the in-situ precipitation of TiO2 phase within Ti3C2 sheets was followed by controlled annealing in temperature range of 500-800 oC for 2 h. The phase and structural characteristics of prepared composites were investigated using X-ray diffraction (XRD), scanning electron microscope (SEM) and differential thermal analysis. The electromagnetic behavior of samples was also analyzed using vector network analyzer (VNA). The results showed that by performing the controlled annealing process of Ti3C2Tx MXene phase, it is possible to in-situ formation of TiO2 phase and form the Ti3C2/TiO2 composites. The electromagnetic behavior of Ti3C2/TiO2 composites is in direct relation with the percentage of TiO2 phase deposited within Ti3C2 sheets during annealing process. The reflection loss (RL) changed from -7.98 to -21.28 dB (within frequency range of 1-18 GHz) with increasing in annealing temperature from 500 to 800 oC as well as increasing the size and percentage of formed TiO2 particles.
